Today, robots can be found helping humans with their daily tasks. Some tasks require the robot to visit a set of locations in the environment efficiently, like in the Traveling Salesman Problem. As indoor environments are maze-like areas, feasible paths connecting locations must be computed beforehand, so they can be combined during the scheduling, which can be impracticable for real-time applications. This work presents an on-line Route Scheduling supported by a Fast Path Planning Method able to adjust pre-built paths. Experiments were carried out with virtual and real robots to evaluate time and quality of tours.

In the original version of this paper the email of the corresponding author, Reza Mahboobi Esfanjani, was given incorrectly. The correct email is mahboobi@sut.ac.ir.

The publisher apologises for this error.

ELEVENTH INTERNATIONAL CONGRESS OF CYBERNETICS AND SYSTEMS

Dedicated to the memory of the late

Professor Frank H. George

Brunel University, Uxbridge (West London),

Middlesex, United Kingdom, 23–27 August 1999

To remove humans from hazardous environments “good” teleoperated robotic systems are needed. “Good” is defined here to mean a system which is task centred and which is transparent to the user-in other words, a system you can see through. A teleoperated robotic system which strives towards this goal is described by way of illustration. The fundamentals that have helped to achieve this are: design and build from a task centred viewpoint, careful design of the Human Computer Interface(HCI) and special consideration for the systems integration task.

Prosthetics presents a challenge for engineers, they must balance user needs with practicalities. In the past the compromises made have been towards simpler devices. Recently this has begun to change, new microprocessors, powerful motors and novel batteries make it possible to conceive of different solutions. These papers give an overview of what is now possible.

An eight-legged walking machine with purely mechanical control of leg motion has been built, based on an old design by Space-General Corporation. The paper describes its mechanical design, and experiments with it on a variety of surfaces.

At the end of the 20th century robot technology became well established as a reliable and economic source in industrial automation. On the other hand, it is claimed that even a general six or seven degree of freedom robot arm or a multifingered robot hand designed carefully and manufactured with very high precision lacks versatility in its use in a variety of tasks that must be done instead of a human. The lack of versatility or the clumsiness of present industrial robots is not due to the fine mechanism of such robots. Rather, the clumsiness shows a lack of our knowledge of everyday physics, in particular, a lack of knowledge of physics involving grasping and handling of various kinds of things and manipulating them with certain dexterity, in which tactile and vision sensings must be well coordinated.

A work cell with multiple robots increases manufacturing flexibility and productivity. Robots in the work cell equipped in a sparse area usually share a motion path, resources and workspace. In this paper, an embedded Markov chain model for a multi-robot system that has a common workspace is constructed on the basis of the concept of a multi-processor system. With the presented model, we measure the performance of error recovery schemes under different workloads and analyze the sensitivity of the execution time with respect to the robot speed. We verify the presented model with an experimental multi-robot work cell. This study is useful in evaluating the performance of a robotic work cell and presents a guide for designing a complex work cell.

In this paper we present an experimental comparison between different decentralized controllers for industrial robot manipulators. In spite of the fact that robot manipulators are highly nonlinear and coupled multivariable systems, decentralized controllers have been widely adopted in industrial environments for trajectory tracking, because of their simplicity and their fault tolerance feature. Different kinds of controllers have been investigated: the typical PID-based controller, a nonlinear three-term controller devised by Tarokh, and a variable structure control law, a discontinuous integral control, both in the continuous and in the discretised version. Allowances are made for the tuning of the parameters in order to obtain low tracking errors. Results show that better performances are obtained by controllers other than PID, especially by the discontinuous integral control, so that they appear to be particularly appropriate for the use in industrial robots.

The mass balancing of robotic manipulators has been shown to have favorable effects on the dynamic characteristics. In actual practice, however, since conventional manipulators have flexibility at their joints, the improved dynamic properties obtainable for rigid manipulators may be influenced by those joint flexibilities. This paper investigates the effects of the joint flexibility on the dynamic properties and the controlled performance of a balanced robotic manipulator. The natural frequency distribution and damping characteristics were investigated through frequency response analyses. To evaluate the dynamic performance a series of simulation studies of the open loop dynamics were made for various trajectories, operating velocities, and joint stiffnesses. These simulations were also carried out for the balanced manipulator with a PD controller built-in inside motor control loop. The results show that, at low speed, the joint flexibility nearly does not influence the performance of the balanced manipulator, but at high speed it tends to render the balanced manipulator susceptible to vibratory motion and yields large joint deformation error.

Fuzzy control has been widely applied in industrial controls and domestic electrical equipment. The automatic learning of fuzzy rules is a key technique in fuzzy control. In this paper, a software development system for fuzzy control is presented. Since the learning of fuzzy rules can be seen as finding the best classifications of fuzzy memberships of input-output variables in a fuzzy controller, it can also be seen as the combination optimization of input-output fuzzy memberships. Multi-layer feedforward network and genetic algorithms (GA) can be used for the automatic learning of fuzzy rules. The algorithms and their characteristics are described. The software development system has been successfully used for the design of some fuzzy controllers.

Autonomous mobile robot navigation systems are based on three principal kinds of techniques: map-based navigation, map-building-based navigation and mapless navigation. We propose a mapless method for trajectory description in unknown indoor environments. The method uses distance measurements from a 2D laser range finder, digitises the robot's visibility area, eliminates superfluous data and reorients their presentation with laws similar to those used in cellular automata. The landmarks are extracted and organised in a panoramic description called fresco. The frescoes which are validated by means of neighbourhood rules. The most informative frescoes are detected by means of two criteria and stored. The stored frescoes are considered as a human-like descritption of the robot's route and could be used by the robot to retrieve its route to its starting point.

Multi-level manipulators are those mechanisms in which two or more levels, that define the main chain of the manipulator, are joined in parallel to each other. Besides, each level is linked to the base in parallel by some limbs. Based on the idea of multi-level manipulators and using the concept of plain leg surfaces, the synthesis of partially decoupled manipulators with five degrees of freedom is presented. Among the different possibilities that exist to design the main chain of the manipulator, one is selected and the different manipulators that can be obtained from this option are analyzed. The concept of control distribution per level is presented and compared with the distribution of degrees of freedom per level. Finally, each of the proposed manipulators is studied and those which decouple the rotations are chosen.

The postural stability of bipedal robots is investigated in perspective of foot-rotation during locomotion. With foot already rotated, the biped is modeled as an underactuated kinematic structure. The stability of such biped robots is analyzed by introducing the concept of rotational stability. The rotational stability investigates whether a biped would lead to a flat-foot posture or the biped would topple over. The rotational stability is quantified as a ground reference point named “rotational stability index (RSI)” point. Conditions are established to achieve rotational stability during biped locomotion using the concept of the RSI point. The applicability of the RSI point is illustrated through experimentation for the landing stability analysis of the bipedal jumping gaits.

The traditional stability criteria such as zero-moment point (ZMP) [M. Vukobratovic and B. Borovac, “Zero-moment point – thirty five years of its life,” Int. J. Humanoid Robot. 1(1), 157–173 (2004)] and foot-rotation indicator (FRI) [A. Goswami, “Postural stability of biped robots and the foot-rotation indicator (FRI) point,” Int. J. Robot. Res. 18(6), 523–533 (1999)] are not applicable to analyze biped's postural stability when foot is already rotated. The RSI point is established as a stability criteria for planar bipedal locomotion in presence of foot rotation.

The work aims to realize energy-efficient bipedal walking by employing the three-mass inverted pendulum model (3MIPM) and compare its energy performance with linear inverted pendulum model (LIPM). To do this, a general optimal index on center of mass (CoM) acceleration is first derived for energetic cost evaluation. After defining the equivalent zero moment point (ZMP) motion, an unconstrained optimization approach for CoM generation is extended for 3MIPM, which can track different ZMP references and address the height variation as well. To make use of the allowable ZMP movement, a constrained optimization method is also employed, contributing to lower energetic cost. Simulation and hardware experiments on a humanoid robot demonstrate that the 3MIPM could achieve higher energy efficiency.

In this paper, an approach to modelling of a robotic assembly cell is proposed and a method for managing the cell operation is described using a knowledge base. Since the modelling structure is based on the concept of the state variable, the relationships between states are described by the state transition map (STM). The knowledge-bases for state transition and assembly job information are obtained from the STM and the assembly job tree (AJT), respectively. Using the knowledge-base, the System structure is discussed in relation to both managing the cell operation and evaluating the performances. Finally, a simulation algorithm is presented with the simulation results to show the significance of the proposed modelling approach.