The enhancement of jet engine components may result in the expansion of the established design space. In particular, the trend towards short and therefore highly aggressive inter compressor ducts (ICD) extends the traditional design space. The potential for fuel savings resulting from a reduction in engine weight is in contrast to the emergence of a more complex flow field. Many studies consider the secondary flow system of highly aggressive ICDs at the design point, but there is a lack of off-design considerations. To fill this gap, the present study investigates in detail the off-design performance of the new German Aerospace Center (DLR) test case. Firstly, computational fluid dynamics (CFD) simulations of different typical operating points allow detailed considerations of the flow field under off-design conditions. Secondly, a variation of the inlet conditions describes the sensitivity of highly aggressive ICDs to different low-pressure compressor operating points. Finally, the comparison of the CFD stagnation pressure loss with the loss predicted by a preliminary off-design method validates the use of traditional off-design prediction during the preliminary design of highly aggressive ICDs.

Thwaites (Aeronaut. Q., vol. 1, 1949, pp. 245–280) developed an approximate method for determining the evolution of laminar boundary layers. The approximation follows from an assumption that the growth of a laminar boundary layer in the presence of pressure gradients could be parameterized solely as a function of the Holstein–Bohlen flow parameter, thus reducing the von Kármán momentum integral to a first-order ordinary differential equation. This method is useful for the analysis of laminar flows, and in computational potential flow solvers to account for the viscous effects. In this work, an approximate method for determining the momentum thickness of a two-dimensional, turbulent boundary layer is proposed following Thwaites’ work. It is shown that the method provides good estimates of the momentum thickness for multiple boundary layers, including both favourable and adverse pressure gradient effects, up to the point of separation. In the limit of high Reynolds numbers, it is possible to derive a criterion for the onset of separation from the proposed model, which is shown to be in agreement with prior empirical observations (Alber, 9th Aerospace Sciences Meeting, 1971). The sensitivity of the separation location with respect to upstream perturbations is also analysed through this model for the NASA/Boeing speed bump and the transonic Bachalo–Johnson bump.

In this study, the aerodynamic performances and the flow separation behaviour of the wing profiles, used in the wing of Boeing 737-Classic aircraft, and a model wing formed of these profiles were investigated at 2 × 105 Reynolds number (Re) and different angles of attack ranging from −4° to the angle, which maximum lift point obtained. The experiments were conducted in a low-speed wind tunnel in Erciyes University Faculty of Aeronautics and Astronautics Aerodynamic Laboratory. Four profiles and the model wing, which was obtained from the combination of the four profiles were produced in a rectangular shape with dimensions of 0.21m × 0.21m. In the first part of this two-part study, the wing profiles were examined individually regarding aerodynamic performance and flow separation. In the second phase of the study, the aerodynamic performance and the flow separation behaviour of the model wing were examined and the results were compared with the data obtained from each profile. The study results showed that the slopes of the numerical graphics are generally quite consistent with experimental results. In addition, the pressure and velocity distributions have followed the normal trend until the angle-of-attack (AoA) of 20°. In contrast, the negative speed values and negative pressure zones have appeared on the profile above this angle. The air flowed as laminar on the profiles and the model wing until 20°, while laminar separation bubbles are begun to take place at about 24° AoA. Finally, the best aerodynamic performance has been obtained with the model wing.

Bernoulli pads can create a significant normal force on an object without contact. The radial outflow which creates this force also imposes a significant shear force on the object. Better understanding this shear force can improve pad designs in order to mitigate material deformation and damage, or allow the pads to be used as shear-based cleaning implements. Here, we use computational fluid dynamics to explore the parameter space and show a power-law relationship between the fluid power at the pad inlet and the maximum shear stress. These simulations are validated by a particle tracking velocimetry experiment. A relationship between the maximum shear stress and the inlet Reynolds number is provided, and some implications of the observed scaling relationships are explored.

In this work, consideration is given to a novel concept for aerofoil lift enhancement and delaying flow separation. Here, lift enhancement is attained by preventing the growth of the boundary layer through the elimination of the zero-slip condition between the wing surface and the air stream. The concept would simulate all the effects of a moving wall, leading to the appearance of a slip velocity at the gas–fluid interface, including the injection of momentum into the air boundary layer, but with one exception: here there is no moving wall but instead a ferrofluid thin film pumped parallel and attached to the wall by a magnetic field. Utilising a simplified physical model for the velocity profile of the ferrofluid film and based on ferrohydrodynamic stability considerations, an analytical expression for the interfacial velocity is derived. Finally, from the available experimental data on moving walls, the expected lift and angle-of-attack enhancement are found as well as the weight penalty per unit surface area of the wing is estimated. Additional research and development is required to explore the possibilities of using ferrofluid thin films.

Experimental analyses of synthetic jet control (SJC) effects on aerodynamic characteristics of rotor in steady state and in hover were conducted. To ensure the structural strength of rotor and enough interior space for holding the synthetic jet actuators (SJAs), a particular blade with a frame-covering structure was designed and processed, and the experiment was conducted with low free stream velocities and rotor rotation speeds. There were three test conditions. In steady state, there were three free stream velocities (10m/s, 15m/s and 20m/s). In hover state, the rotor was worked with two rotation speeds of 180RPM and 240RPM. In forward flight, the rotor was worked with a rotation speed of 180RPM and a free stream velocity of 7.5m/s. To measure the synthetic jet control effect on rotor in stall, the range of collective pitch was set from 10° to 28° in steady state. The aerodynamic forces and sectional velocity field were measured by using the six-component balance and the Particle Image Velocimetry (PIV) system in the wind tunnel. Flow control effects on the blade based on the synthetic jets (SJ) were experimentally investigated with different jet parameters, such as jet locations, jet angles, and jet velocities. In steady state, the jet closer to the leading edge, and the jet angle of 90° had more advantages in improving the aerodynamic characteristics. Furthermore, the aerodynamic forces and sectional velocity field measurement of rotor in hover were conducted, it showed that SJAs could increase flow velocity at the upper surface, which led to lower upper surface pressure. As a result, the normal forces of rotor with two rotation speeds were increased significantly. These results indicated that the synthetic jet has a capability of increasing the normal force and delaying or preventing the stall of rotor.

Flow over a moderately swept wing is characterised by complex localised flow vortex topologies such as ‘closed’ separation bubbles or ‘open’ separation structures. A model of a complex cambered, twisted, tapered wing with 40° leading edge sweep, representative of those designed for manoeuvre at high subsonic Mach numbers, was investigated using the oil-film visualisation, stereo particle image velocimetry and force moment measurements. Wind-tunnel tests were conducted at a range of Reynolds number from 2.1×105 to 8.4×105 and at angles of incidence from −1° to 22°. Still images combined with video clips enable flow patterns over the wing model to be interpreted more clearly and accurately. Using successive images extracted from the video of flow visualisation, the movement of the oil pigment has been estimated. The influence of the Reynolds number and incidence angle was discussed through analysing the flow pattern over the wing surface. Additionally, the link between the flow structures present and the wing aerodynamic performance was studied.