Hostname: page-component-745bb68f8f-mzp66 Total loading time: 0 Render date: 2025-02-11T19:41:40.992Z Has data issue: false hasContentIssue false
  • English
  • Français

Tribomechanical Property Modification of Commercial TiN Coatings by Carbon Ion Implantation

Published online by Cambridge University Press:  22 February 2011

L.J. Liu ,
D.K. Sood  and
R.R. Manory
L.J. Liu
Affiliation:
Microelectronics and Materials Technology Centre, Royal Melbourne Institute of Technology, 124 La Trobe Street, Melbourne 3000, Australia.
D.K. Sood
Affiliation:
Microelectronics and Materials Technology Centre, Royal Melbourne Institute of Technology, 124 La Trobe Street, Melbourne 3000, Australia.
R.R. Manory
Affiliation:
Department of Chemical and Metallurgical Engineering.
Get access

Abstract

About 2 μm thick commercial coatings of TiN on high speed steel substrates were implanted at room temperature with 95 keV carbon to nominal doses between 1 × 1017 and 8×1017 ions cm-2. An ultra-microhardness apparatus (UMIS-2000) was used to measure hardness, and a pin-on-disc machine (CSEM Tribometer) with a sapphire ball was used to measure wear, friction and adhesion. Carbon implantation induced a significant improvement in ultra-microhardness, friction coefficient and wear properties. The surface microhardness increases monotonically by up to 115% until a critical dose φ crit is reached. Beyond this dose the hardness decreases, but remains higher than that of unimplanted sample. A lower friction coefficient and a longer transition period towards a steady state condition were obtained by implantation. An improvement of up to four times in the wear is obtained after carbon implantation. Topology studies with SEM show a change in the mode of wear. The changes in tribomechanical properties are discussed in terms of radiation damage and possible second phase formation.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 316: Symposium A – Materials Synthesis and Processing Using Ion Beams , 1993 , 563
Copyright
Copyright © Materials Research Society 1994

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

6. References

1 Habig, K.H., Surf. Coat. Technol., 42, 133 (1990).Google Scholar
2 Vetter, J. and Rochotzki, R., Thin Solid Films, 192, 253 (1990).Google Scholar
3 Rochotzki, R., Vetter, J. and Weiβmantel, E., Thin Solid Films, 198, 103 (1991).Google Scholar
4 Braun, M., Nucl. Instr. Meth., B59, 914 (1991).Google Scholar
5 Roos, J.R., Celis, J.P. and Franck, M., Surf. Coat. Technol., 45, 89 (1991).Google Scholar
6 Kulkarni, A.V., Mate, N., Kanetkar, S.M. and Ogale, S.B., Surf. Coat. Technol., 54/55, 508 (1992).Google Scholar
7 Liu, L.J., Zhou, W., Sood, D.K. and Manory, R.R., MRS Symposia Proceedings, 279, 469 (1993).Google Scholar
8 Koerber, F.G., Petersein, H. and Ranke, H., Thin Solid Films, 181, 505 (1989).Google Scholar
9 Culbertson, R.J., Bums, F.C., Franzen, W., Lewder, L.J., Ricca, J.J. and Gonzales, A., Nucl. Instr. Meth., B56/57, 652 (1991).Google Scholar
10 Bunker, S.N. and Armini, A.J., Nucl. Instr. Meth., B39, 7 (1989).Google Scholar
11 Braun, M. and Kylner, C. (unpublished results, private communication).Google Scholar
12 Perry, A.J. and Schoenes, J., Vacuum, 36, 149 (1986).Google Scholar
13 Pamler, W., Huttingerand, M. Bentsch, W., Thin Solid Films, 174, 143 (1989).Google Scholar
14 Biersack, J.P. and Haggmark, L.G., Nucl. Instr. Meth., 174, 257 (1980).Google Scholar
15 Liu, L.J., Sood, D.K., Manory, R.R. and Zhou, W., Surf. Coat. Technol. (to be published).Google Scholar
16 Kant, R.A. and Sartwell, B.D., Mater. Sci. and Eng., 90, 357 (1987).Google Scholar
17 Hutchings, R. and Oliver, W.C., Wear, 92, 143 (1983).Google Scholar