Hostname: page-component-6bf8c574d5-mggfc Total loading time: 0 Render date: 2025-02-15T10:08:49.450Z Has data issue: false hasContentIssue false
  • English
  • Français

Prediction of the Fiber-Matrix Interface Failure due to Longitudinal Tensile Loading Using Finite Element Methods

Published online by Cambridge University Press:  15 February 2011

Hassan Mahfuz ,
A.K.M. Ahsan Mian ,
Uday K. Vaidya ,
Timothy Brown  and
Shaik Jeelani
Hassan Mahfuz
Affiliation:
Materials Research Laboratory, Tuskegee University, Tuskegee, Alabama
A.K.M. Ahsan Mian
Affiliation:
Materials Research Laboratory, Tuskegee University, Tuskegee, Alabama
Uday K. Vaidya
Affiliation:
Materials Research Laboratory, Tuskegee University, Tuskegee, Alabama
Timothy Brown
Affiliation:
Materials Research Laboratory, Tuskegee University, Tuskegee, Alabama
Shaik Jeelani
Affiliation:
Materials Research Laboratory, Tuskegee University, Tuskegee, Alabama
Get access

Abstract

A 3D-unit cell for 0/90 laminated composites has been developed to predict the composite behavior under longitudinal tensile loading condition. 3D contact element has been used to model the fiber matrix interface. Two interface conditions, namely, infinitely strong and weakly bonded, are considered in the analysis. Both large displacement and plastic strain behavior for the matrix are considered to account for the geometric and material non-linearities. Investigations were carried out at three temperatures to compare the composite response obtained from mechanical tests at those temperatures. Stress-strain behavior and the local stress distributions at the fiber as well as at the matrix are presented, and their effects on the failure of the interface are discussed in the paper. The material under investigation was SiCf/Si3N4.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 365: Symposium M – Ceramic Matrix Composites–Advanced High-Temperature Structural Materials , 1994 , 229
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Mahfuz, H., Xue, D. and Jeelani, S.,“Response of SiC Coated Carbon-Carbon Composites at Room and Elevated Temparatures under Tensile Loading", Composite Science and Technology, 50(1994), pp. 411–422.Google Scholar
2. Folias, E.S.,“On the Prediction of Failure at a Fiber/Matrix Interface in a Composite Subjected to a Transverse Loading”, Journal of Composite Materials, Vol. 25-July 1991, pp. 869–886.Google Scholar
3. , Brun Milivoj, K., “Measurement of Fiber/Matrix Interface Shear Stress at Elevated Temperatures”, J. Am. Ceram. Soc., 75(7) 1914–17 (1992).Google Scholar
4. , Homes, John, W., “Influence of Stress ratio on the Elevated-Temperature Fatigue of a Silicon Carbide Fiber-Reinforced Silicon Nitride Composite”, J. Am. Ceram. Soc., 74(7) 1639–45 (1991).Google Scholar
5. , Homes, John, W., “Tensile Creep Behavior of a Fiber-Reiforced SiC-Si3N4 Composite”, Journal of Materials Science, 26:1808–14 Apr. 1991.Google Scholar
6. Nimmer, Ronald P., Bankert, R.J., Russel, Edward S., Smith, Gary A., and Wright, P. Kennard, “Micromechanical Modeling of Fiber/Matrix Interface Effects in Transversely Loaded SiC/Ti-6-4 Metal Matrix Composites”, Journal of Composite Technology and Research, Vol 13, No. 1, Spring 1991, pp. 3–13.Google Scholar
7. Nimmer, Ronald P., “Fiber-Matrix Interface Effects in the Presence of Thermally Induced Residual Stresses”, Journal of Composites Technology & research, Vol. 12, No. 2, Summer 1990, pp. 65–75.Google Scholar