Hostname: page-component-6bf8c574d5-vmclg Total loading time: 0 Render date: 2025-02-15T09:59:13.567Z Has data issue: false hasContentIssue false
  • English
  • Français

The Effect of Low-Angle and High-Angle Grain Boundaries on Elevated Temperature Strength

Published online by Cambridge University Press:  15 February 2011

M. E. Kassner
M. E. Kassner*
Affiliation:
Department of Mechanical Engineering, Center for Advanced Materials Research, Oregon State University, Corvallis, OR 97331, USA
Get access

Abstract

The influence of small (subgrain) misorientation interfaces on the mechanical behavior of metals and alloys deforming within the creep regime has been intensively studied over the past several decades. Controversies have existed, but some new experiments suggest, contrary to the general opinion, that low-angle boundaries are not associated with the rate controlling process for plasticity and do not affect strength. The new evidence will be discussed in terms of other established experimental trends. Large-angle boundaries may have a smaller effect on elevated temperature strength than at ambient temperatures and do not appear to dramatically affect elevated temperature strength. Superplastic effects are not addressed.

Type
Aricles
Information
MRS Online Proceedings Library (OPL) , Volume 362: Symposium J – Grain-Size and Mechanical Properties--Fundamentals and Applications , 1994 , 157
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Yavari, P. and Langdon, T.G., Acta. Metall. 30, 2181 (1982).Google Scholar
2. Porrier, J.P., Rev. Phys. Appl. 11, 731 (1976).Google Scholar
3. Sherby, O.D. and Weertman, J., Acta Metall. 27, 387 (1979).Google Scholar
4. Sherby, O.D. and Burke, P., Prog. Mater. Sci. 13, 325 (1968).Google Scholar
5. Morris, M.A. and Martin, J.L., Acta Metall. 32, 1609 (1984).Google Scholar
6. Morris, M.A. and Martin, J.L., Acta Metall. 32, 549 (1984).Google Scholar
7. Blum, W., Phys. Status Solidi. 45, 561 (1971).Google Scholar
8. Weertman, J., Creep and Fracture of Engineering Materials and Structures, edited by Wilshire, B. (Pineridge, Swansea, U.K., 1984), p. 1.Google Scholar
9. Weckert, E. and Blum, W., Strength of Metals and Alloys, edited by McQueen, H.J., Bailon, J.-P., Dickson, J.I., Jones, J.J., and Akben, M.G. (Pergamon Press, Oxford, 1985), p. 773.Google Scholar
10. Bendersky, L., Rosen, A., and Mukherjee, A.K., Int. Met. Rev. 30, 1 (1985).Google Scholar
11. Maruyama, K., Karshima, S., and Oikawa, H., Res. Mechanica 7, 21 (1983).Google Scholar
12. Argon, A.S. and Takeuchi, S., Acta Metall. 29, 1877 (1981).Google Scholar
13. Derby, B. and Ashby, M.S., Acta Metall. 35, 1349 (1987).Google Scholar
14. Sherby, O.D., Klundt, R.J., and Miller, A.K., Metall. Trans. A, 1977, 843.Google Scholar
15. Nabarro, F.R.N., Acta Metall. Mater. 38, 637 (1990).Google Scholar
16. Orlova, A. and Cadek, J., Mater. Sci. and Eng. 77, 1 (1986).Google Scholar
17. Calliard, D. and Martin, J.L., Acta Metall. 30, 791 (1982).Google Scholar
18. Ardell, A.J. and Przstupa, M.A., Mech. Mater. 3, 319 (1984).Google Scholar
19. Evans, H.E. and Knowles, G., Acta Metall. 25, 963 (1977).Google Scholar
20. Kassner, M.E., Miller, A.K., and Sherby, O.D., Metall. Trans. 13A, 1977 (1982).Google Scholar
21. Kassner, M.E., Ziaai-Moayyed, A.A., and Miller, A.K., Metall. Trans. 16A, 1069 (1985).Google Scholar
22. Kassner, M.E., J. Mater. Sci. 25, 1997 (1990).Google Scholar
23. McLean, D., Trans. AIME 22, 1193 (1968).Google Scholar
24. Ostrom, P. and Lagneborg, R., Res. Mechanica 1, 59 (1980).Google Scholar
25. Parker, J.D. and Wilshire, B., Phil. Mag. 41A, 665 (1980).Google Scholar
26. Widersich, H., J. Met. 16, 423 (1964).Google Scholar
27. Kassner, M.E., Modelling the Deformation of Crystalline Solids, edited by Lowe, T.C., Rollett, A.D., Follansbee, P.S. and Daehn, G.S. (TMS, Warrendell, PA, 1991), p. 309 Google Scholar
28. Young, C.M., Robinson, S.L., and Sherby, O.D., Acta Metall. 23, 633 (1975).Google Scholar
29. Henshall, G.A., Kassner, M.E. and McQueen, H.J., Metall. Trans. 23A, 882 (1992).Google Scholar
30. Kassner, M.E., Mater. Sci. and Eng. A166, 81 (1993).Google Scholar
31. Al-Haidary, J.T., Petch, M.J., and Rios, E.R. Delos, Phil. Mag. 47, 868 (1983).Google Scholar
32. Kassner, M.E. and Li, X., Scripta. Met. et Mater. 25, 2833 (1991).Google Scholar
33. Kikuchi, S. and Yamaguchi, A., in Strength of Metals and Alloys, edited by McQueen, H.J., Bailon, J.-P., Dickson, J.I., Jonas, J.J., and Akben, M.G.) (Pergamon Press, Oxford, 1985), p. 899.Google Scholar
34. Kassner, M.E., and McMahon, M.E., Metall. Trans. 18A, 835 (1987).Google Scholar